HV-
Insulation Meter PeakTech PKT-2680
HV-Insulation Meter with up to 5,000 measurements / according
to VDE 0413 part 1 /
Simplified selection of test voltage / with 6-digit display
|
The
HV - insulation meter PeakTech PKT-2680 is one of a series of highly accurate
and robust meters. It is equipped with a 6-digit display. That HV-insulation
meter has been developed especially for for the on-field operations and to
operate despite of difficult measuring conditions. Integral protection circuits
for the prevention of measurement defaults due to stray currents are one of the
many benefits of this HV- insulation meter. The HV-insulation meter is equipped
with a CMOS micro processor and features an acoustic and an optic alarm signal.
Due to this HV-insulation meter the operator can work with 5 kV test voltages,
for example. It also supports performing effective insulation measurements in
high voltage facilities. The unlimited calibration accuracy of the HV-insulation
meter is widely assured, since the HV-insulation meter was calibrated by the
manufacturer onto highly accurate digital measurements (stored as EEPROM
memory). Definition for insulation resistance: It is the resistance measured in
Ohm at electrical facilities). Thus it is of highest priority for the operator
protection against electric shocks and regarding the prevention and avoidance of
material damage due to uncontrolled flowing leakage current. By means of
insulation tests the state of insulations can be measured and rated.
If there are any questions about this HV-Insulation Meter PeakTech PKT-2680, please have a look at the technical specification below or
call: UK customers +44(0) 23 809 870 30 / US customers +1-410-387-7703. Our technicians and engineers will gladly advise you in all insulation-meters
and all products in the field of measuring
instruments, regulation
and control and scales.
|
|
|
-
6-digit LCD display
- Measurement according to VDE 0413 part 1
- Test voltage up to 5,000 V
|
-
Simplified selection of test voltage
- EMV: EN 50081- 1, EN 50082- 1
- Safety: IEC-1010-1; CAT III
|
Technical Specifications
|
DC-
Test
Voltage
|
500
/ 1.000 /
2.500 /5.000 V
|
Insulation
measurement ranges
|
30
GΩ / 500 V
60 GΩ / 1.000 V
150 GΩ / 2.500 V
300 GΩ / 5.000 V
|
Accuracy
|
±
5 % + 2 dgt.
|
Maximum
of capacitive load
|
1
Watt
|
Insulation
resistance between electrical lines and enclosure
|
2000
MΩ / 2000V
|
Withstand
voltage between electric circuit and enclosure
|
7000
V AC for a max. of 1 minute
|
AC-
alarming set-up
|
at
voltages of > 450 V AC
|
Short-circuit
current
|
1
mA
|
Operational
voltage
|
8
x 1.5 V batteries (UM3, AA)
|
Dimensions
|
250
x 190 x 110 mm (WxHxD)
|
Weight
|
1.5
kg
|
Delivery
Content
|
1
x HV-insulation meter PeakTech PKT-2680
1 x Protection Case
1 x color-coded flexible silicone test-leads
1 x integrally protected Ultra-HV probe head in coaxial silicone conductor
1 x AAA batteries
1 x instruction manual
|
|
Performing
an insulation check by means of the HV- insulation meter:
- Switch off voltage
- Cut connection between neutral and ground and earth conductor
- Switch of circuit breaker, fuse, GFCI and consumer
- Connect first measuring lead between phase and earth conductor, afterwards
between phase and neutral conductor, then start the insulation meter and
measure. It seams to make sense to measure among the phases themselves, in order
to detect damages or aging processes of the conductors better. The minimal
values of the insulation resistances should be at a measurement voltage of 250 V
DC 0.25 Ohm, at 500 V 0.5 Ohm, at 1000 V DC 1 MOhm.
|
|
|
Similar
products to the HV-Insulation Tester PeakTech PKT-2680: |